Switch Powered Liftgate Movement On or Off
Change the liftgate from full powered movement to unlatch-only behavior when carrying an accessory or servicing the rear area.
Liftgates, trunks, tailgates, storage, cargo hardware, roofs and practical utility functions.
Each guide keeps its market, model-year, powertrain and equipment limits attached. A listed model does not imply the feature is standard on every trim.
Change the liftgate from full powered movement to unlatch-only behavior when carrying an accessory or servicing the rear area.
Slide the available step and grab handle out of the tailgate for easier bed access.
Raise the equipped open power tailgate about 4 in (10 cm) to trigger closing.
Use the equipped tailgate's tablet slot, tool recess, clamp pockets, ruler and cup holder.
Use the instrument-panel or touchscreen control in normal operation and the two-pull service release only after a power failure.
Open the power frunk with its exterior button, the SecuriCode keypad or an authorized Phone as a Key.
Relocate both support cables to the tailgate strikers and install the safety bracket for supported long cargo.
Identify the molded bed slots and use fitted lumber as cross-supports for loads that need a raised or divided platform.
An equipped 2024 Ranger tailgate combines clamp pockets, a ruler, cup holder, bottle opener and bag holder in the lowered work surface.
Arm the liftgate after locking, then remain in its rear detection zone with the smart key for three seconds.
Enable the setting, wait after locking and remain behind the vehicle with the smart key for three seconds.
Store a manual opening point and choose User Height Setting so the liftgate returns to it automatically.
Enable the setting, wait 15 seconds after locking and remain in the rear detection zone for three seconds.
Store a manual height and select User Height Setting, or choose one of four preset opening levels.
Enable Open Only, approach from beyond 10 feet with the fob and remain near the liftgate through four chimes.
Release the two lid handles, lift the storage cover correctly, and relock it after loading.
Fold the rear seats, support the midgate from outside and use short or long switch presses for the desired opening.
Open the MultiPro inner panel, power the independent 100-watt KICKER system and pair a phone over Bluetooth without running the truck radio.
Turn off the defroster, fold the seats, release both upper latches and lock the glass into the Midgate storage pocket.
Lower the primary and inner gates, then unfold the inner panel to create the 48-inch-wide, 375-pound-rated step.
Turn on hands-free rear access, cancel an unwanted automatic opening, and store a lower power-liftgate height.
Approach with the key fob and make one straight one-second in-and-out kick over the projected GMC logo.
Move the open liftgate to a safe height, hold the latch-area button for confirmation and use the 3/4 setting to recall it.
Store a lower opening position for garages with limited clearance or easier reach.
Use one upward-and-back foot motion at the center sensor while carrying the Smart Entry remote.
Open or close the tailgate from the key fob, driver's control or the tailgate button.
Trigger the powered tailgate from the center of the rear bumper while carrying the Smart Entry remote.
Choose a conventional drop-down opening or a side-swing opening for closer access to the bed and In-Bed Trunk.
Power suitable equipment from the covered Black Edition bed outlet, with higher output available while the engine runs.
Store wet or valuable cargo in the lockable 7.3-cu-ft bed compartment and disable its lock release for valet use.
Enable the feature, lock the vehicle and remain in the rear detection area with the smart key until the opening alert finishes.
Enable the option, wait after locking and remain in the rear detection area with the smart key through the six-chime alert.
Operate the liftgate from the smart key, instrument panel or liftgate-mounted buttons and pause travel with another press.
Reinitialize liftgate travel after a 12-volt battery or related fuse has been removed, replaced or recharged.
Enable the feature, lock the Santa Fe for 15 seconds and remain in the rear detection zone with the smart key.
Move the liftgate to the preferred height, store it from the inner button and select User Height Setting in the display.
Open the matching vehicle guide and read its availability note first. When the retail trim or package is not named by the official source, use the window sticker, manufacturer build record or the visible control in the vehicle.